HEDON USER MANUAL

Title

GENERAL ADVICE ON HELMET USE

TABLE OF CONTENT

GENERAL ADVICE ON HELMET USE

 

HOW TO USE A DOUBLE D RING

 

HEROINE RACER 2.0 (FULL FACE WITH INBUILT VISOR)

• How to change a visor on a Heroine Racer 2.0

• How to remove and replace cheekpads on a Heroine Racer 2.0

• How to install a Sena Bluetooth system on a Heroine Racer 2.0

 

HEROINE RACER 1.0 (FULL FACE WITH INBUILT VISOR)

• How to change a visor on a Heroine Racer 1.0

• Heroine Racer 1.0 Visor Mechanism

• Fitting Bluetooth on a Version 1.0 Racer

 

HOW TO PUT AN ANTI-FOG LENS ON A VISOR

 

HEDONIST (OPEN FACE)

• How to snap a sun peak on a Hedonist

• How to snap a visor on a Hedonist

 

EPICURIST (OPEN FACE WITH INBUILT VISOR)

• How to change a visor on an Epicurist

 

EDENIST (E-BIKE)

• How to use a fidlock buckle on an Edenist

 

HEDSTRONG (CYCLE)

• How to use a fidlock buckle on a Hedstrong

 

CARE & CLEANING

WARRANTY

LIMITATIONS OF WARRANTY

CERTIFICATION

RETURNS POLICY

WARNING

PRODUCT REGISTRATION

GENERAL ADVICE ON HELMET USE

Your helmet has been specially designed and developed in the Hedon workshop to make sure it protects you in the best possible way. Please read the following instructions carefully before using your helmet.Keep these instructions in a safe place for future reference when maintaining your helmet.

 

• The box in which your helmet has been delivered ensures that it has been protected from impacts since it was manufactured, provided such box is not damaged.

• To provide adequate protection, the helmet must fit correctly on your head and be well fastened. (Please see Fig1.1 below on how to securely fasten your helmet) It should be snug and comfortable. 

• Never wear a helmet too far back on your head. (Please see Fig1.2) To protect you properly, it must cover your forehead. Always secure the buckle tightly to keep your helmet firmly placed whenever you ride. In any case, before starting off, make sure that the buckle is secure and tight. 

• With the helmet on and the straps fastened and pulled tight, try to remove the helmet from your head. Grasp it securely and make a serious effort to roll it off your head by moving it forwards and backwards. If you cannot remove this helmet, it does not roll backward far enough to expose your forehead or forward enough to block your vision, you have a proper fit. 

• It is not safe if a helmet is improperly fitted or fastened on the head as the helmet may “roll off” the head in a collision or at any time. 

• Avoid prolonged exposure to strong sunlight as this may affect the paint work. If the helmet has sustained an impact, even if there are no signs of damage, replace it immediately.• If the visor is marked «day time use only», users shouldn’t use it at night or in any condition with poor visibility.

Fig1.1

Fig1.2

HOW TO USE A DOUBLE D RING

FOR ALL MOTORCYCLE HELMETS

Title

It is extremely important that you secure your helmet correctly and firmly before you ride.Here are some instructions on how to do so. If you still have problems, please contact us at info@hedon,com for us to help you.

 

1.) Lead chinstrap through eyelets of both Double D rings. 

2.) Curl back and thread through taller ring with red leather pull-tab.

3.)  Securely tighten strap until comfortable and safe. 

4.) Press and snap buttons together to manage excess strap.

Watch video to see how to buckle a double D ring.

HEROINE RACER 2.0 (FULL FACE WITH INBUILT VISOR)

Title

Read about why the 2.0 is so much better.

Read why

HOW TO CHANGE A VISOR ON 
A HEROINE RACER 2.0

HOW TO REMOVE AND REPLACE CHEEKPADS ON A HEROINE RACER 2.0

DIFFERENT CHEEKPAD THICKNESSES

We are always working tirelessly to provide the best fit to our riders. This meant creating 3 different thicknesses for our luscious leather upholstered cheek pads. Each helmet comes with a standard thickness of 30 mm foam on the inside and there is an option to buy a thinner pair with the foam at 27 mm or a thicker pair at 43 mm.

ORDER NOW

HOW TO INSTALL A SENA BLUE TOOTH SYSTEM ON A HEROINE 2.0

HEROINE RACER 1.0 (FULL FACE WITH INBUILT VISOR

Title

HOW TO CHANGE A VISOR ON A HEROINE RACER 1.0

HEROINE RACER 1.0 VISOR MECHANISM

Prior to embarking on any ride, it is imperative to conduct a thorough inspection of your CNC screws. This safety check serves as the critical line of defence against potential visor-related issues stemming from improper or insecure attachment, which can lead to screws loosening during your ride. Taking a moment for this quick examination can make all the difference.

 

Should you encounter any concerns with your ratchet or CNC screw, we urge you to reach out to us promptly. Our dedicated team is here to provide you with the best possible assistance and support to ensure your safety and riding experience remain exceptional.

 

You can message us on the live chat now or send us an email at aftersales@hedon.com

FITTING BLUETOOTH ON A VERSION 1.0

To fit sena/cardo system, it need to be retro-fitted by only us so please contact us for help. 

If your visor gets creaky and squeaky, apply some WD40 on the visor.

HOW PUT AN ANTI-FOG LENS ON YOUR VISOR

HEDONIST (OPEN FACE)

Title

HOW TO SNAP A VISOR ON A HEDONIST

Each Hedonist has a very good range of complementary accessories that can be snapped on to the poppers on the helmet. There is a proper way to snap them on so that you don't scratch your helmet by accident and also to do it as smoothly as possible.

EPICURIST (OPEN FACE WITH INBUILT VISOR)

Title

HOW TO CHANGE AN EPICURIST VISOR

EDENIST (OPEN FACE E-BIKE)

Title

HOW TO USE AN EDENIST

HEDSTRONG (CYCLE HELMET)

Title

HOW TO USE A HEDSTRONG

CARE & CLEANING

Title

• When cleaning any visor, only use warm water and neutral soap. Never use window Cleaning products. DO NOT use any solvents. Note that with each and every clean it will affect the fog and scratch resistant on the visor. In order to keep all parts of the helmets in their best conditions, use a wet cloth to clean the chinstrap and other relevant areas. 

• Never apply paints, stickers, petrol or other chemical solvents to the helmet and visor. 

• For cleaning the lining of your motorcycle helmet, use a clean damp cloth with some soap and have a good wipe all over the lining, scrubbing lightly on the areas you would like to be cleaned. Then leave it to dry completely before you wear it. 

• For the cleaning of the matte helmet surfaces - Usually water and neutral soap will suffice for cleaning the surface of the helmet but for more stubborn stains 100% cleaning alcohol and evenly applied pressure from a micro fibre cloth is quite effective. 

• For glossy helmet surfaces - Water and neutral soap with a micro fibre cloth will suffice. For a good polish you can use car wax as all our helmets are painted with the same painting and techniques of automobiles. 

• For hardware maintenance - If you are tired of the oxidised look of some of the hardware on your helmet you can polish them with a mixture of lemon and salt and gently rub all over the surfaces of the hardware. For the EPICURIST and HEROINE screws make sure to remove the screws from the helmet for polishing and to make sure they are secured correctly and firmly back on the helmet after. 

• For leather maintenance - you can apply leather conditioner or shoe polish for richer colour and protection. 

• For the lining of the motorcycle helmets, use a cloth damp with some warm soapy water and wipe the down the surface for dirt and then let it completely dry before puttting it back on. 

• For the lining of the Ebike helmets, This lining is removable. Remove it and handwash delicately in a basin without soaking the leather pieces. let it dry completely before putting it back on.

WARRANTY

Title

Hedon guarantees that the helmet’s materials and manufacturing will meet specifications for a period of 1 year from the date of purchase or 2 years from date of purchase, if you register your helmet with Hedon. To do so, please follow the registration procedure under ‘Product Registration’. If the helmet shows visible defects in the materials or manufacturing during the guarantee period, you can return your helmet. To return your helmet you must contact Hedon prior to taking any action at aftersales@hedon.com . Hedon’s liability is limited to the cost of repair and/or replacement of the item during the warranty period.This warranty does not apply in the case of defects other than materials or manufacturing. The warranty does not cover the following cases:

• Products modified by the purchaser or a third party

• Deterioration that is not a result of defects in materials or manufacturing

• Use of the helmet not in compliance with this User Manual – Warranty

• Any other reason such as sizing or choice of colour and model

LIMITATIONS OF WARRANTY

Title

TERMS, CONDITIONS AND WARRANTIES (INCLUDING ANY WARRANTY AS TO MERCHANTABLE QUALITY OR FITNESS FOR A PARTICULAR PURPOSE) IMPLIED BY COMMON LAW OR STATUTE (“IMPLIED WARRANTIES”) AS TO THE QUALITY OR SPECIFICATIONS OF THE HELMET ARE EXCLUDED UNLESS THE EXCLUSION OF ANY SUCH IMPLIED WARRANTIES WOULD CONTRAVENE APPLICABLE LAW OR CAUSE ANY PART OF THIS WARRANTY TO BE VOID. THE WARRANTIES, OBLIGATIONS AND LIABILITIES OF MANUFACTURER HEREUNDER ARE EXCLUSIVE. MANUFACTURER WILL UNDER NO CIRCUMSTANCES BE LIABLE FOR ANY INDIRECT OR CONSEQUENTIAL DAMAGE ARISING FROM THE USE OF THE HELMET.Warning: (1) THE helmet cannot protect against all possible impacts, and serious injury or death could occur WHILE WEARING THE HELMET.(2) Improperly fitted OR FASTENED helmet may “roll off” the head in a collision OR AT ANYTIME. for maximum protection the helmet must be fitted and attached properly to the wearer’s head in accordance with the manufacturer’s fitting instructions.(3) After receiving an impact, the helmet may be damaged to the point that it is no longer adequate to protect the head against further impacts. this damage may not be visible to the user. a helmet that has sustained an impact should be destroyed and replaced.Dispute Resolution: Any dispute relating to this warranty, the materials or manufacturing of the helmet shall be resolved according to the laws of England and Wales. Any dispute will be settled exclusively in accordance with the procedures set forth herein. All arbitration, proceedings and hearings will be conducted in the English language in accordance with the Model Law on International Commercial Arbitration and the UNCITRAL arbitration rules then in force. All decisions and awards rendered by the arbitrator will be final and binding upon the parties for all questions submitted to such arbitrator and the costs associated with such submission shall be shared equally by the parties involved in the Dispute unless the arbitrator decides otherwise. The parties waive all rights of appeal therefore to any court or tribunal, and agree that the only recourse by any party to any court will be for the purpose of enforcing an arbitration award.Any conduct which recognizes the existence of this Manual User - Warranty, including but not limited to the purchase of the helmet by user shall constitute acceptance of this User Manual - Warranty and all of its terms and conditions.

RETURNS POLICY

Title

Products can be returned within 14 days from proof of purchase. This only applies if it is purchased from our webshop www.hedon.com. Please fill out the return form on our site. (You can go straight to the form with the button below.Products and it’s packaging must be in mint condition. Please read on our website under ‘Return Policy’ carefully on how to pack the helmet properly for a return and refund. All products returned within 14 days of purchase will not be charged any postal charges for the return shipment. Anything after 14 days there will be an additional charge for the return shipment. ( this only applies to the United Kingdom ). For the rest of the world, all products returned within 14 days of purchase will be eligible a full refund except for all the postal charges incurred. Any return that is something other than a manufacturing defect (i.e, wrong sizing, etc..) and after a period of 14 days after purchase, the Purchaser will have to be charged for all of the return postage.

 

All products that are bought from our site only can be returned with a full refund if the products returned are checked and verified by us that they are in mint condition, including the packaging. All products must be packed according to our packing instructions to avoid any damage. This excludes customised helmets and sample helmets, there are no returns on these helmets.Please note damaged helmets will be charged at 50% RRP + Shipping Costs.Please read carefully and follow the step by step instructions provided here below.Please note the above form must be completed within 14 days of receipt of items for returns to be accepted, with the exception of manufacturing defects.We only offer FREE RETURNS or size exchanges and manufacturing defects for customers in the United Kingdom within 14 days from receipt of order. Returns for any other reason and/or out of the 14 day period will be charged postal charges. Returns for size exchanges or refunds from outside the UK will be charged postal fees.All returns must be managed by us, such as organizing the courier for pick up and drop off. This is so we can track the products clearly. All Purchasers will be sent an invoice for the return shipment, once payment is received we will organise the pick up accordingly.For all Epicurist helmets, DO NOT REMOVE STICKER ON THE VISORS until you are sure the helmet fits you. We will not accept any returns for any Epicurist helmets without the stickers on both sides.This Return Policy is only valid for products purchased on www.hedon.com

WARNING

Title

HELMETS

Your helmet has been specially designed and developed in the Hedon Workshop to make sure it protects you in the best possible way. Please read the following instructions carefully before using your helmet.

 

Keep these instructions in a safe place for future reference when maintaining your helmet. The box in which your helmet has been delivered ensures that it has been protected from impacts since it was manufactured, provided such box is not damaged. To provide adequate protection, the helmet must fit correctly on your head and be well fastened. (Please see Fig1.1 on how to securely fasten your helmet) It should be snug and comfortable. Never wear a helmet too far back on your head. To protect you properly, it must cover your forehead. Always secure the buckle tightly to keep your helmet firmly placed whenever you ride. In any case, before starting off, make sure that the buckle is secure and tight. With the helmet on and the straps fastened and pulled tight, try to remove the helmet from your head. Grasp it securely and make a serious effort to roll it off your head by moving it forwards and backwards. If you cannot remove this helmet, it does not roll backward far enough to expose your forehead or forward enough to block your vision, you have a proper fit. Avoid prolonged exposure to strong sunlight as this may affect the paint work. If the helmet has sustained an impact, even if there are no signs of damage, replace it immediately. If the visor is marked «daytime use only», users shouldn’t use it at night or in any condition with poor visibility. It is not safe if a helmet is improperly fitted or fastened on the head as the helmet may “roll off” the head in a collision or at any time. For the Racer, Remove the protective sticker on the visor. Remove the protective stickers on the fancy round screws that attach the visor to the helmet by unscrewing the screws first as the sticker might be lodged in between the visor and the screw. Lastly, make sure those screws are secured firmly before you put on the helmet and ride. No helmet can protect against all possible impacts and serious in jury, or death could occur while wearing the helmet. After receiving an impact, the helmet may be damaged to the point that it is no longer adequate to protect the head against further impacts.This damage may not be visible to the user. A helmet that has sustained an impact should be destroyed and replaced.

 

VISOR

Before you use the helmet, check that the visor and visor screws are securely tightened. The visor and visor screws should be checked periodically. Re-tighten any loose screws before riding. 

 

Dirt and scratches on the visor may obstruct your view while riding and can be very dangerous. If the visor has scratches obstructing your vision, replace it immediately. The visor should be cleaned with a solution of mild, neutral soap and water. Rinse well with pure water then wipe dry with a soft cloth. Do not use any of the following cleaning materials: hot water over 40°C; salt water; any acidic or alkali detergent; benzine, thinner, gasoline, or other organic solvents; glass cleaner; or any cleaner containing organic solvents. If any of these cleaners are used you may damage the visor’s surface.

CERTIFICATION

Title

All motorcycle helmets sold in the EU are ECE.22.05 certified which means they are road legal in the whole of Europe and the UK.All of our helmets sold in North America are DOT certified (Federal Motor Vehicle Safety Standard 218).EDENIST range is certified , NTA 8776: 2017 , EN 1078: 2012 + A1: 2012 and CPSC. HEDSTRONG cycle range is certified EN 1078: 2012 + A1: 2012 and CPSC

PRODUCT REGISTRATION

Title

Please register your helmet on our website www.hedon.com under “Registration”. This will extend your warranty to 2 years.

REGISTER MY HELMET